Search results for query: *

The discussions regarding new pricing and the termination of annual programming have caused me to look at my programming options again; unfortunately, I can't find a comprehensive list that details all of the associated programming fees and charges, and under what circumstances they're...

Slightly off topic, but I've searched the forum looking for a pointer to a detailed list of programming related charges and fees, but haven't found anything. The Dish site lists some fees (like on site repairs, shipping fees, etc.) but doesn't seem to have a detailed list of charges. Where's the...

If what others have stated here is correct, it sounds like I'll be billed at a new, higher rate in May, before the end of my annual contract (October), as opposed to the contract running it's course and then having new monthly rates apply.

Yes, they're applying what I paid, but I'd expect Dish honor the original agreement. Discontinuing annual contracts should mean that I can't renew again, as opposed to ending the agreement mid stream. I'm sure there's a "we reserve the right to change at any time" clause somewhere, but I would...

Well, I was very disappointed to receive the notice. I've been an annual subscriber since 1996. The wording in the letter was a bit vague to me, so I contacted Dish and was told that the annual "balance" that would be applied to the new monthly charges meant I wouldn't pay anything more until...

It's possible for compressed air to generate a static charge and damage components, but I've never actually seen it happen. It seems more likely that something else happened when you disconnected/reconnected the cable. Perhaps there's a cold solder joint/mechanical issue where the socket joins...

No, no OTA module. To eliminate as many variables as possible, I now have the coax runs from ports 1 and 2 on the 1000.4 LNB going to the receiver inputs 1 and 2 (triplexer removed). Each of the runs are ~65' from the LNB to the ground block, then another ~20' to the receiver (no wall plates)...

Just wanted to update this thread since it's referenced in another post..... I continued to see the LNB drift warning and incrementing count of signal losses, and I lost several recordings due to signal loss. My final troubleshooting step was to run a new temporary piece of coaxial cable from...

I'm wondering if anyone knows whether Dish offers a repair and/or exchange service for receivers for a flat rate or one time fee. The receiver is a 722k that I purchased (not leased). I'm not participating in any new subscriber offers (I'm an old timer; 15 years w/Dish) or the equipment...

So I replaced my LNB, and at the same time removed the triplexer from the system so that I have two coax runs from ports 1 and 2 on the LNB to inputs 1 and 2 on the receiver. I performed a check switch, checked signal strength, checked system status (it still reported the exact same LNB drift...

You nailed it.... the T1 and T3 (305?) T-berd was what popped into my head. I used to maintain three DS-3 cross connects feeding telco Rockwell 21130 multiplexers and smaller Fujitsu three channel muxes. Our T3 transport was for proprietary video, but each video T3 had four T1 channels carved...

Oh..... I thought the -13 was a negative exponent value; that's how bit error rate was always designated for T1/T3 circuits and such. So it looks like it is time for a new LNB. Thanks for the input everyone.

Well, I checked again last nght, and definitely have the most trouble when switching to TBS or HGTV; all other channels seem fine. The LNB drift indicator gave some hex values that didn't mean anything to me except for the negative exponent value (like bit error rate). The reading was 0X1C...

I'll check for LNB drift; and for the poster that asked about OTA, I don't have a module installed. I get my off-air channels off-air (directly to my TV tuner).

I'm looking for help with a really odd signal problem. I've got a one and a half year old Eastern arc 1.4 installation with a single 722k receiver and have been experiencing increasingly frequent "signal loss" messages. The message will intermittently occur when powering up or changing channels...

Well, I had an odd experience today.... There was a new "primary receiver fee" of $9 on my monthly statement. I'm an annual AT120 sub. and have never had any addtional fees until I replaced my 508 DVR with a new 722 I purchased, and had the $6/month DVR fee added. The Dish CSR told me all annual...

I'm finding a significant increase in responsiveness..... much, much better than before. Thanks so much for putting the effort into the updates.

A quick look at your connectors and a check for LNB connectivity/functionality might be in order.... If you run a "check switch", you should either see signal results, or an indication of the 1000.4 system and three "connected" messages, one for each LNB, if there is no satellite signal at all...

You're thinking is (somewhat) correct on each satellite signal being on one of the three ports, but the LNB assembly has the ability to send the signal from any one of the three individual LNB's to any one of the three output ports. The default state of the assembly is to send the signals from...

Perhaps a sun transit? It is that time of the year, but you'd have to check the date/time for your location and the 61.5 satellite.

I posted this in another thread, but I ended up finding the footprint maps for E1, E4, and E8 at the 77 position, and none of the U.S. beams on those cover Maine. I'm in an outer contour on one or two beams, and that's where I get the signal level of 25. There's just very little signal to begin...

When you select the orbital locations on the signal strength screen, does the message below the signal bar actually identify the correct satellites by name? If you're truly seeing 61.5 only on port 1, with no lock on 2 and 3, you may have the reflector too far toward the East. As MikeD-C05 says...

Well, if I'm reading the maps (that I just discovered) correctly, I've been wasting my time and Maine is outside even the lowest receive level contour of all three satellites in the 77 position, although we're in a fringe area for one satellite's high power beam..... D'oh!

I received my new reflector yesterday, and overall my signal levels incresed by 4 or 5 points (apparently the dents in the original reflector were having a measurable impact on performance). However, the situation with 77 remains the same. On xponder 21 at 61.5 I see a level of 55, and at 72.7...

Oddly enough, when I installed my new reflector yesterday, I ended up with the same results at 77. My overall signal levels were up a few points on each position, but 77 is still about 1/2 the others.