I cannot get all 3 sats to line up. can anyone help?

[GMWILLY]

I have a 3 lnb system at my cabin and I am using my box from home with current card which I have the slimline at home, the box recognizes all 3 dishes, 101, 110, & 119 but I cant get them all at once just one per movement and i am set to the correct info on the box, anyone know what i should do next?
Thanks

 

[GMWILLY]

I CANT GET ALL 3 SIGNALS AT ONCE ONLY SEPERATE AT ONCE

I have a 3 lnb system at my cabin and I am using my box from home with current card which I have the slimline at home, the box recognizes all 3 dishes, 101, 110, & 119 but I cant get them all at once just one per movement and i am set to the correct info on the box, anyone know what i should do next? And i get all even number transponders on 101 but no odd numbers and i get all transponders on 110 and 119. I have literally been out there for 6 hours and i am frustrated.
Please help
Thanks

dish- wnc triple feed multi sat lnb
model# au2-f1

receiver- model# d12-100
swm-1 satellite in is what it says where the coax goes in.

my home zip is 55110
my cabin zip is 54751

I am using one cable from sat to box going to only 1 t.v.
dish says built in multi-switch

any other info needed let me know

thanks again

 

[twizt3dsist3r]

get a cheap signal meter and repeak the dish

 

[jdspencer]

Tune to chs 490-494, these verify reception on those sats.

What transponders have signals on the three sats?
Do you get any odd TPs from 119?

 

[Jimbo]

I have a 3 lnb system at my cabin and I am using my box from home with current card which I have the slimline at home, the box recognizes all 3 dishes, 101, 110, & 119 but I cant get them all at once just one per movement and i am set to the correct info on the box, anyone know what i should do next?
Thanks

Have you set your "Tilt" correctly ?

 

[jdspencer]

See my reply in your other thread.
Which is now post #4 above.

 

[Jimbo]

OP, try to keep your post asking the same question, in the same thread.
I gave you my opinion in your other post.

 

[digiblur]

Merged duplicate threads.

 

[GMWILLY]

Sorry about the duplicate threads, this was my first post. I aligned my dish by the receiver which is 72 azimuth and 35 tilt and 206 direction in which i get 110 but nothing else. on 110 and 119 i get all transponders. I would be happy just getting 101 and watching something but the receiver wont let me and I also tuned to 490-493 and it just says searching for signal.
Thanks

 

[harshness]

206 degrees is the azimuth (direction), 35 is the elevation (from level) and 72 is the skew (dish needs to be slanted to the right of horizontal).

I bet that if you use the numbers for the parameters that they are actually associated with, you'll have much better luck.

 

[jdspencer]

Sorry about the duplicate threads, this was my first post. I aligned my dish by the receiver which is 72 azimuth and 35 tilt and 206 direction in which i get 110 but nothing else. on 110 and 119 i get all transponders. I would be happy just getting 101 and watching something but the receiver wont let me and I also tuned to 490-493 and it just says searching for signal.
Thanks

You aren't aligned properly. FYI, with 101 you should get all 32 transponders with the exception of a few spot beams. On 110, you should only get 3 TPs, 8, 10, and 12. With 119 you can only get TPs 22-32, with the exception of a few spot beams. I'm guessing that your 110 LNB is receiving the 101 sat. So try moving the dish 9 degrees to the west. and verify your alignment parameters as harshness pointed out.