Search results for query: *

  1. C

    coolsat6000 reboots every 2sec.

    Thank you. Found firmware. Was able to load the firmware. Problem fixed.
  2. C

    coolsat6000 reboots every 2sec.

    Thank you.
  3. C

    coolsat6000 reboots every 2sec.

    Thank you. Where do i find the firmware.
  4. C

    coolsat6000 reboots every 2sec.

    Hi, need help I was watchig tv and my coolsat6000 started to reboot by it self. The box is not modified. Any idia. Thank you
  5. C

    Loosing signal when changing chanels

    I'll try Thanks
  6. C

    Loosing signal when changing chanels

    It happends on "H" polarity. Wich are good LNBs?
  7. C

    Loosing signal when changing chanels

    Hallo all, I have cs4 and cs6 connected through two separate diseq switches to two dual lnb receiving from two sats. When i change chanel on one receiver i am loosing signal on the other receiver for 1 to 3 seconds (bad or no signal). What is wrong? Please advise. Thanks
  8. C

    cs4000pro, no 13V and 18V

    I am glad too that is fixed. The heatsink is under power and is isolated from gnd ( the tab of LM317 is under power - the ouput, You are correct) Thanks for the help again.
  9. C

    cs4000pro, no 13V and 18V

    Problem solved HI, and Thank You. I replaced LM317 as You sugested and bang everething is ok. Now I have 13V, 18V, and 0V when off. When I removed IC I noted that there was no heat transfer compound between heat sink and IC. I did it the proper way and now is ok Thank You guys You are grait.
  10. C

    cs4000pro, no 13V and 18V

    Hi again. I was going to go in bed, then I sed I have to check it now. So 10ohm drops output voltage to 21.51V only. I will buy Lm317 and will cross my fingers. Thanks again for the support.
  11. C

    cs4000pro, no 13V and 18V

    Hi, I just found 10ohm resistor. I will test again and if i dont get 1.25V I vill replace LM317. Thank you.
  12. C

    cs4000pro, no 13V and 18V

    Hi, and thank you. I did not have at the moment 10ohm resistor. I found 1k. If does not help al buy 10 ohm and will check again. Grounded adj pin with 1k as it is on the board (assuming there is ~2.7k to gnd in circuit) so will get less than 1k to gnd. Voltage on output changed from 23.74v...
  13. C

    cs4000pro, no 13V and 18V

    Very funy! Hi, thanks to you I needed 1h and found that it is LM317 - 3-terminal adj. voltage regulator- wich controls the voltage to LNB. Possibly controled by transistor pnp on adj pin on input = 23.82V output = 23.76V adjust = 21.6V I found that resistance betw. input and output is...
  14. C

    cs4000pro, no 13V and 18V

    Thank You very much. It sounds very profesional. I will try this and I will let you now. Thank you
  15. C

    cs4000pro, no 13V and 18V

    Tried. Does not change voltage. Thanks
  16. C

    cs4000pro, no 13V and 18V

    No. I am using factory installed software. I am afraid to connect it in this condition. Is it software or hardware problem? Thanks
  17. C

    cs4000pro, no 13V and 18V

    Hi, need help. I have coolsat4000pro. I mesure 23VDC on connector to LNB - back of receiver. I don't mesure 13VDC and 18VDC needed for LNB operation. The 23V is even present with LNB power off in dish settings. Please, need help how to fix. Thank You
Top
Back