Search results for query: *

I play around with it lol if I can help let me know

somehow i ended up in advanced english class ..... sometimes life is amazing :)

the laser i used was a 5 mW it wasn't bright enough to see during the daylight, anyone got suggestions on the the power laser to use

I have a BUD and want to review, the C1W and C1 PLL, too

Ken pictures would be nice sounds like you have a non-pen (penetrating) mount that has a 3 inch pole a 8 ft dish would need a large non-pen mount usually these are 8X8 the smaller mounts are for smaller dishes but most weld shops should be able to fab up an adapter if thats the route...

Top markings is the skew side markings is the f/D

I'm currently working in the Richmond area , so I'm close if you need some help will be off work on Monday & Tuesday

if you attempt to remove the lnbf be careful most all of these are aluminum rod stock (the support arms) and will break easy after being there a long time . a wire brush and a penetrating oil might help lots of threads here on sattellite guys on birdviews installs & refurbs and welcome: to...

I want to move my dish

ok i'm no expert at it but did get the chance to play with multi lnb's on one dish for a few hours last year . I don't get a lot of time to play with my dishes since i work out of state. this link shows several lnb's in a temp setup using conduit hangers. although they are flimsy and...

personally i would convert the 7.5 ft sami to a 4 pole using electrical conduit ( like Fat Air mentioned) probably the cheapest route . if needed i can get the length of my unimesh 7.5 length of poles should be close . i'm currently not close to my unimesh to get you a comparison on fd but...

I wire brush mine and use pb blaster tapping like mentioned above . heat from torch like mentioned above works also afterwards i clean nut and threads with wire brush & after installing i paint them

Best memories are going to Grandmas house around Christmas. Enjoying family and friends Then We would eat after Grandma and my aunts and mother had cooked everything we liked. Amiko A3 or ASC1 :) thanks for the contest

Dee-ann i aways like reading your posts :) not for the misery part but the story :) i have the other version of your dish which i hope to pull down next year and rehab a bit seems to have a bit of aged parts and hail damage ... 10 ft ODOM with 4 feedhorn support arms :) although...

run fast , quickly and run far .. delete your browser history too ok you was warned :)

C2PLL Wideband ™ :)

Robert here's a pic of the receiver , there should be a receiver section here on satguys or ask.... i'm sure someone here has the same receiver its a solomend hd-pvr800 I think it was also commonly called a Skybox S9 HD PVR800 or Openbox S9

they started using them after the planet X virus :)

I would agree with the others finding a local dish probably for free is a great option.. also for ku if you like keeping it on a separate dish the old primestar dishes work great.... If you need a receiver to start with and play around with send me a PM i've got a couple older boxes that...

ok parts used for this prototype 1 clamp 4" harbor freight on sale this week $1.99 1 laser cross beam $1.10 1 AA battery holder $0.72 1 automotive clip $0.59 1 mending plate 1/2" X 3" $0.24 1 zip tie $0.03 1 screw (i had) $0.05 electrical tape and soilder ( i had) no cost build cost...

ok i meant to try it about 1 hour before it got dark but i missed that cause i was working on another project. 1st is lnbf with flash on second is lnbf with no flash 3rd is scaler with flash and 4th is without flash also note i didn't adjust laser for scaler so its pointing about 1/2 inch...

first two pics are of prototype 3rd pic is cross hairs on deep freezer at 2 ft lights on 4th pic is cross hairs on deep freezer at 2 ft lights off 5th pic is mounted to lnbf 6 pic is of laser pointer mounted to the side on same tool, its mounted about 3/8 inch toward right and this is...

Well my first prototype is great ...... well there are some problems :) seems it can only be used in low light areas to traverse the distance from lnbf to dish seems my laser light isn't powerful enough :( I bought a cheap crosshair type laser (650nm 5mW 3V Red Laser Cross Module Head)...

Congratulations Primestar :)

its my intentions to make a signal passing design