Search results for query: transponder+power

The LNB power may be turned off in the receiver's installation menu. Check that the LNB power setting is set to Automatic or 13/18. If the LNB power is set on, use a voltage tester to see if the coax cable at the LNBF is reading 13Vdc on a vertical transponder and 18Vdc on a horizontal...

The motor is correctly installed and the latitude is correctly set to your install latitude. The dish elevation angle should be set to 39 degrees on the mount scale, according to the STAB HH90 manual. The photo does not show the scale for a 39 degree setting (it is on the other side of the...

El Bandido was able to replicate my issue on his system: So, he believes it's NOT the Start TV on 3965 V that's "taking over" Movies! on 3961 V, it's the higher-powered (maybe Sun outage temp?) version of Start Tv at 3708 that's doing it. I didn't even know that was there, but who knows...

Where is the DiSEqC switch located? Where is the multi-switch located? Is the multi-switch powered or passive? Is the dish grounded? If so, where? Is the dish ground bonded to the structure ground? Test the LNB voltage on both vertical and horizontal transponders. Check for voltage potential...

Considering that it's a small dish, and that the LNBF polarization does not match the satellite polarization, 42% might be all you're getting. I tried it yesterday with a much larger dish and I don't think i was getting more than 60%. Having the wrong polarization type means that not only are...

I have a question, can we use a different generic lnbf for Anik F1 107.3W satellite instead of KUSAT F1x twin offered by Kusat? Perhaps an lnb with the same technical specs than the Kusat F1x twin. Or definitely there's no other lnb that can be used?

My question was more along the lines of how does the receiver communicate to the LNB which polarity it wants (unless vertical is always the default polarity). I'm given to believe that there were different switching schemes employed depending on the Primestar LNB used.

We it uses voltage to power the LNB however since all the transponders (both of them) use the same polarity then I am told you can use a splitter for multi room installs. (No switch needed) Sent from my iPhone using SatelliteGuys

It doesn't matter if they quit broadcasting to customers from 110 & 119, so long as they have satellites up there they are fulfilling the conditions of their license. When those satellites get old, if they don't move something into place then they are no longer fulfilling the terms of their...

45W could be a bit of a challenge as it's not very powerful. But 30W should be easy (i can get most transponders with a re-purposed DT Slimline), while 34.5W is a bit more difficult here but should be stronger in FL.

The 117W bird, Eutelsat 117A (formerly SatMex 8) is a FSS (fixed satellite service) satellite, I looked to try and find the power levels of the Ku transponders, but couldn't find any information. Generally they are not as powerful as the BSS (broadcast satellite service) birds that DirecTV and...

Will test more after the ORBY TV LNBF arrives. Yes, quality copper stinger, quad shield RG-6 with clean DigiCon fittings. Yes, there will be a voltage drop, but 5Vdc drop would be abnormal. Most of us would not have horizontal channels with a LNBF if there was a 5Vdc drop on a 125' coax...

As I was reading the thread about the new Edision and got flashback about this. The last time I played with Enigma 2 was on a DGStation (about 10 years ago) and it took for ever to scan for channels. I would start the scan, eat dinner, come back and it was still scanning. After it is done, I...

Well, spec-wise, it should be doable with a minibud. Same specs as the Lesea mux. As for the Shepherds Chapel, that's dvb-s2 8psk Fec 3/4, which means you need a C/N of 7.9, that should be harder to get. Perhaps they are doing something else with the signal, not pushing full power, etc. Just...

Can't set it to standard and get 10750, but in universal I can set the start to 10750, but then it has a second, not sure if I have to set that. I can set the elevation to 53.2 per the dish pointer, and it shows which way to point, but I get nothing above a small yellow level. I put the dish...

It sounds like you have an Amiko receiver. Set the LNB to Standard (10750 is the starting frequency). I would start with 97W, it is a very strong satellite with many different high-powered transponders :) I've never had much luck with those simple tone signal meters. If you are able, take the...

There are no issues with these ABC feeds, but a dish and feed must be perfectly optimized to reliably receive them. If you are receiving both vertical and horizontal channels on different satellites, the servo motor and the wiring are working fine. BTW, you purchased the servo on Ebay from me...

There's no particular reason why it should have lower signal quality, Directv is authorized for the same power level as Ka and Ku. Either they are broadcasting reverse band at a lower power level for some reason, or there is something in the design of the reverse band LNB that causes it be...

That satellite (Eutelsat 117WA) has 3 Ku beams: - Hemi - covers most of the Americas - NAFTA - US, Mexico, Southern Canada, a bit of Guatemala - South America - does not include Central America (cuts off in Panama) (there's also Eutelsat 117WB but all of its transponders are in lower Ku band)...

yes, probably,but i'm interested if anyone has actually measured it. In SWM mode you don't actually need the 13/18v transponder selection voltage.

Hi, Hope someone can help me out there with this "minor" issue, but all my channels seem to work although sometimes a 'light' rain will cause some satellite searching. I have a H23-600 receiver with a sl5s4nr5-01 SWM LNB (5 satellite LNB), there is just this one receiver connected directly to...

USALS is a calculated aiming program that works with USALS HH motors to automatically aim a calibrated dish/motor at the selected satellite. Typically it is used for KU band motors. It does not work with DiSEqC 1.2 based controllers. There are a few KU motor install guides on this site that...

Update. I pulled the antenna off the mast and changed it to the numbers from dishpointer.com.while the antenna was off the mast I corrected it to be level, it was off a small amount. I pointed the antenna to the general direction shown on the dishpointer.com web site. I rotated the antenna very...

I went ahead and ordered the satmeter brt203 mentioned and I have another dish coming on wednesday. Yes, I'm using the freesat tuner that many people use successfully. changing the transponder settings did not help. I still just see 60% signal and 0% quality. It seems like 60% kicks in just as...

F2 traditionally was the HD bird but there are several transponders on F1R now that carry HD. Beginning in spring of 2019 as standard definition signals are dropped and the final conversion to an almost entirely HD lineup happens most of what is on F2 will be moved to F1R. F2 is getting old...